 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| (R) ISL6535 Data Sheet May 5, 2008 FN9255.1 Synchronous Buck Pulse-Width Modulator (PWM) Controller The ISL6535 is a high performance synchronous controller for demanding DC/DC converter applications. It provides overcurrent fault protection and is designed to safely startup into prebiased output loads. The output voltage of the converter can be precisely regulated to as low as 0.597V, with a maximum tolerance of 1% over the commercial temperature range, and 1.5% over the industrial temperature range. The ISL6535 provides simple, single feedback loop, voltagemode control with fast transient response. It includes a trianglewave oscillator that is adjustable from below 50kHz to over 1.5MHz. Full (0% to 100%) PWM duty cycle support is provided. The error amplifier features a 15MHz gain-bandwidth product and 6V/s slew rate which enables high converter bandwidth for fast transient performance. The ISL6535's overcurrent protection monitors the current by using the rDS(ON) of the upper MOSFET, which eliminates the need for a current sensing resistor. Features * Operates from +12V Input * Excellent Output Voltage Regulation - 0.597V Internal Reference - 1% Over the Commercial Temperature Range - 1.5% Over the Industrial Temperature Range * Simple Single-Loop Control Design - Voltage-Mode PWM Control * Fast Transient Response - High-Bandwidth Error Amplifier - Full 0% to 100% Duty Ratio - Leading and Falling Edge Modulation * Small Converter Size - Constant Frequency Operation - Oscillator Programmable from 50kHz to Over 1.5MHz * 12V High Speed MOSFET Gate Drivers - 2.0A Source/3A Sink at 12V Low Side Gate Drive - 1.25A Source/2A Sink at 12V High Side Gate Drive - Drives Two N-Channel MOSFETs * Overcurrent Fault Monitor - High-Side MOSFET's rDS(ON) Sensing - Reduced ~120ns Blanking Time * Converter can Source and Sink Current * Soft-Start Done and an External Reference Pin for Tracking Applications are Available in the QFN Package * Pin Compatible with ISL6522 * Supports Start-Up into Prebiased Loads * Pb-free available (RoHS compliant) Pinouts ISL6535 (14 LD SOIC) TOP VIEW RT 1 OCSET 2 SS 3 COMP 4 FB 5 EN 6 GND 7 14 VCC 13 PVCC 12 LGATE 11 PGND 10 BOOT 9 UGATE 8 PHASE Applications * Power Supply for some Pentium(R), PowerPCTM, as well as Graphic CPUs * High-Power 12V Input DC/DC Regulators * Low-Voltage Distributed Power Supplies Ordering Information ISL6535 (16 LD QFN) TOP VIEW SSDONE OCSET VCC PART NUMBER (Note) ISL6535IBZ* PART MARKING 6535IBZ 65 35IRZ TEMP. RANGE (C) 0 to +70 0 to +70 PACKAGE (Pb-free) 14 Ld SOIC PKG. DWG. # M14.15 M14.15 RT ISL6535CBZ* 6535CBZ ISL6535CRZ* 65 35CRZ 16 SS COMP FB EN 1 2 3 4 5 REFIN 15 14 13 12 PVCC 11 LGATE 10 PGND 9 BOOT -40 to +85 14 Ld SOIC 16 Ld 4x4 QFN L16.4x4 ISL6535IRZ* -40 to +85 16 Ld 4x4 QFN L16.4x4 *Add "-T" or "-TK" suffix for tape and reel. Please refer to TB347 for details on reel specifications. NOTE: These Intersil Pb-free plastic packaged products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate PLUS ANNEAL - e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2006, 2007. All Rights Reserved All other trademarks mentioned are the property of their respective owners. 6 GND 7 PHASE 8 UGATE 1 ISL6535 Block Diagram EN SS VCC OCSET INTERNAL REGULATOR 30A 6A REFERENCE VREF = 0.597V BOOT REFIN (QFN ONLY) SOFT-START AND FAULT LOGIC SOURCE OCP UGATE POWER-ON RESET (POR) 200A FB EA PWM GATE CONTROL LOGIC PHASE COMP OSCILLATOR PVCC LGATE GND PGND SSDONE (QFN ONLY) RT 2 FN9255.1 May 5, 2008 ISL6535 Simplified Power System Diagram ROCSET +12V Cvcc Q1 +1.2V TO +12VIN LOUT VOUT ISL6535 RFS COUT Q2 CSS R2 R1 Typical Application +12VIN LIN RFILTER CF2 CF1 VCC PVCC BOOT ROCSET OCSET SSDONE (QFN ONLY) REFIN (QFN ONLY) UGATE LOUT PHASE EN LGATE Q2 CHFOUT CBOUT VOUT COCSET Q1 CBOOT DBOOT CHFIN CBIN PGND RRT RT ISL6535 SS CSS COMP C2 C1 R2 FB R1 GND RO C3 R3 3 FN9255.1 May 5, 2008 ISL6535 Absolute Maximum Ratings Supply Voltage, VPVCC,VVCC . . . . . . . . . . . . . . GND - 0.3V to +16V Enable Voltage, VEN . . . . . . . . . . . . . . . . . . . . . GND - 0.3V to +16V Soft-start Done Voltage, VSSDONE . . . . . . . . . . GND - 0.3V to +16V Boot Voltage, VBOOT . . . . . . . . . . . . . . . . . . . . . GND - 0.3V to +36V Phase Voltage, VPHASE . . . . . . . . . VBOOT - 16V to VBOOT + 0.3V All Other Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . GND - 0.3V to 5.0V ESD Rating ESD Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Class 2 Thermal Information Thermal Resistance (Typical) JA (C/W) JC (C/W) SOIC Package (Note 1) . . . . . . . . . . . . 95 N/A QFN Package (Note 2). . . . . . . . . . . . . 47 8.5 Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . +150C Maximum Storage Temperature Range . . . . . . . . . .-65C to +150C Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp Operating Conditions Supply Voltage, VVCC . . . . . . . . . . . . . . . . . . . . . . . . . . +12V 10% Supply Voltage, VPVCC . . . . . . . . . . . . . . . . . . . . . . . . . +12V 10% Boot to Phase Voltage, VBOOT - VPHASE . . . . . . . . . . . . . . NOTES: 1. JA is measured with the component mounted on an evaluation PC board in free air. 2. JA is measured in free air with the component mounted on a high effective thermal conductivity test board with "direct attach" features. See Tech Brief TB379. For JC, the "case temp" location is the center of the exposed metal pad on the package underside. 3. Limits should be considered typical and are not production tested. Electrical Specifications PARAMETER VCC SUPPLY CURRENT Shutdown Supply VCC Shutdown Supply VPVCC POWER-ON RESET VCC/VPVCC Rising Threshold VCC/VPVCC Hysteresis OCSET Rising Threshold OCSET Hysteresis Enable - Rising Threshold Enable - Hysteresis OSCILLATOR Trim Test Frequency Total Variation Ramp Amplitude ERROR AMPLIFIER DC Gain Gain-Bandwidth Product Slew Rate PROTECTION OCSET Current OCSET Current OCSET Measurement Offset Recommended Operating Conditions, unless otherwise noted specifications in bold are valid for process, temperature, and line operating conditions. SYMBOL TEST CONDITIONS MIN TYP MAX UNITS IVCC IPVCC SS/EN = 0V SS/EN = 0V 3.5 0.30 6.1 0.5 8.5 0.75 mA mA 6.45 170 0.70 180 1.4 175 7.10 250 0.73 200 1.5 250 7.55 500 0.75 220 1.60 325 V mV V mV V mV RRT = OPEN VVCC = 12 8k < RRT to GND < 200k (Note 3) VOSC RRT = OPEN 175 1.7 200 15 1.9 220 2.15 kHz % VP-P RL = 10k, CL= 100pF (Note 3) GBWP SR RL = 10k, CL= 100pF (Note 3) RL = 10k, CL= 100pF (Note 3) - 88 15 6 - dB MHz V/s IOCSET IOCSET TJ = 0C to +70C TJ = -40C to +85C 180 176 - 200 200 10 220 224 - A A mV OCPOFFSET OCSET= 1.5V to 15.4V (Note 3) 4 FN9255.1 May 5, 2008 ISL6535 Electrical Specifications PARAMETER Soft-start Current REFERENCE Reference Voltage TJ = 0C to +70C TJ = -40C to +85C System Accuracy TJ = 0C to +70C TJ = -40C to +85C REFIN Current Source (QFN Only) REFIN Threshold (QFN Only) REFIN Offset (QFN Only) GATE DRIVERS Upper Drive Source Current Upper Drive Source Impedance Upper Drive Sink Current Upper Drive Sink Impedance Lower Drive Source Current Lower Drive Source Impedance Lower Drive Sink Current Lower Drive Sink Impedance SSDONE (QFN ONLY) SSDONE Low Output Voltage ISSDONE = 2mA 0.30 V IU_SOURCE VBOOT - VPHASE = 12V, 3nF Load (Note 3) 1.25 2.0 2 1.3 2 1.3 3 0.94 A A A A 0.591 0.588 -1.0 -1.5 -4 2.10 -3 0.597 0.597 -6 0.603 0.606 1.0 1.5 -8 3.50 3 V V % % A V mV Recommended Operating Conditions, unless otherwise noted specifications in bold are valid for process, temperature, and line operating conditions. (Continued) SYMBOL ISS TEST CONDITIONS MIN 22 TYP 30 MAX 38 UNITS A RU_SOURCE 90mA Source Current IU_SINK RU_SINK IL_SOURCE VBOOT - VPHASE = 12V, 3nF Load (Note 3) 90mA Source Current VPVCC = 12V, 3nF Load (Note 3) RL_SOURCE 90mA Source Current IL_SINK RL_SINK VPVCC = 12V, 3nF Load (Note 3) 90mA Source Current Typical Performance Curves 80 RRT PULL-UP TO +12V IPVCC+VCC (mA) 70 60 50 40 30 20 10 0 100 200 300 400 500 CGATE = 10pF 600 700 800 900 1000 CGATE = 3300pF CGATE = 1000pF 1000 RESISTANCE (k) 100 RRT PULLDOWN TO GND 10 10k 100k SWITCHING FREQUENCY (Hz) 1M SWITCHING FREQUENCY (kHz) FIGURE 1. RRT RESISTANCE vs FREQUENCY FIGURE 2. BIAS SUPPLY CURRENT vs FREQUENCY 5 FN9255.1 May 5, 2008 ISL6535 Functional Pin Description (SOIC/QFN) RT (Pin 1/14) This pin provides oscillator switching frequency adjustment. By placing a resistor (RRT) from this pin to GND, the switching frequency is set from between 200kHz and 1.5MHz according Equation 1: . 6500 R RT [ k ] ------------------------------------------------------ - 1.3k F s [ kHz ] - 200 [ kHz ] BOOT (Pin 10/9) This pin provides bias to the upper MOSFET driver. A bootstrap circuit may be used to create a BOOT voltage suitable to drive a standard N-Channel MOSFET. PGND (Pin 11/10) This is the power ground connection. Tie the lower MOSFET source and board ground to this pin. (RRT to GND) (EQ. 1) LGATE (Pin 12/11) Connect LGATE to the lower MOSFET gate. This pin provides the gate drive for the lower MOSFET. Alternately ISL6535's switching frequency can be lowered from 200kHz to 50kHz by connecting the RT pin with a resistor to VCC according to Equation 2: 55000 R RT [ k ] ------------------------------------------------------ + 70k 200 [ kHz ] - F s [ kHz ] PVCC (Pin 13/12) Provide a 12V 10% bias supply for the lower gate drive to this pin. This pin should be bypassed with a capacitor to PGND. (RRT to VCC) (EQ. 2) OCSET (Pin 2/15) The current limit is programmed by connecting this pin with a resistor and capacitor to the drain of the high side MOSEFT. A 200mA current source develops a voltage across the resistor, which is then compared with the voltage developed across the high side MOSFET. A blanking period of 120ns is provided for noise immunity. VCC (Pin 14/13) Provide a 12V bias supply for the chip to this pin. The pin should be bypassed with a capacitor to GND. REFIN (QFN ONLY Pin 5) Upon enable if REFIN is less than 2.2V, the external reference pin is used as the control reference instead of the internal 0.597V reference. An internal 6A pull-up to 5V is provided for disabling this functionality. SS (Pin 3/1) Connect a capacitor from this pin to ground. This capacitor, along with an internal 30A current source, sets the soft-start interval of the converter. SSDONE (QFN ONLY Pin 16) Provides an open drain signal at the end of soft-start. COMP (Pin 4/2) and FB (Pin 5/3) COMP and FB are the available external pins of the error amplifier. The FB pin is the inverting input of the error amplifier and the COMP pin is the error amplifier output. These pins are used to compensate the voltage-control feedback loop of the converter. Functional Description Initialization The ISL6535 automatically initializes upon receipt of power. Special sequencing of the input supplies is not necessary. The Power-On Reset (POR) function continually monitors the bias voltage at the VCC pin and the driver input on the PVCC pin. When the voltages at VCC and PVCC exceed their rising POR thresholds, a 30A current source driving the SS pin is enabled. Upon the SS pin exceeding 1V, the ISL6535 begins ramping the non-inverting input of the error amplifier from GND to the System Reference. During initialization the MOSFET drivers, pull UGATE to PHASE and LGATE to PGND. EN (Pin 6/4) This pin is a TTL compatible input. Pull this pin below 0.8V to disable the converter. In shutdown the soft-start pin is discharged and the UGATE and LGATE pins are held low. GND (Pin 7/6) Signal ground for the IC. All voltage levels are measured with respect to this pin. Soft-start During soft-start, an internal 30A current source charges the external capacitor (CSS) on the SS pin up to ~4V. If the ISL6535 is utilizing the internal reference, then as the SS pin's voltage ramps from 1V to 3V, the soft-start function scales the reference input (positive terminal of error amp) from GND to VREF (0.597V nominal). If the ISL6535 is utilizing an externally supplied reference, when the voltage on the SS pin reaches 1V, the internal reference input (into of the error amp) ramps from GND to the externally supplied reference at the same rate as the voltage on the SS pin. Figure 3 shows a typical soft-start interval. The rise time of the output voltage is, FN9255.1 May 5, 2008 PHASE (Pin 8/7) This pin connects to the source of the high side MOSFET and the drain of the low side MOSFET. This pin represents the return path for the high side gate driver. During normal switching, this pin is used for high side current sensing. UGATE (Pin 9/8) Connect UGATE to the upper MOSFET gate. This pin provides the gate drive for the upper MOSFET. 6 ISL6535 therefore, dependent upon the value of the soft-start capacitor, CSS. If the internal reference is used, then the soft-start capacitance value can be calculated through Equation 3: 30A t SS C SS = ---------------------------2V (EQ. 3) VSS Overcurrent Protection VSSDONE If an external reference is used, then the soft start capacitance can be calculated through Equation 4: 30A t SS C SS = ---------------------------V REFEXT (EQ. 4) IOCP VEN ILOAD VOUT tHICCUP FIGURE 4. TYPICAL OVERCURRENT PROTECTION VSS tSS FIGURE 3. TYPICAL SOFT-START INTERVAL Prebiased Load Startup Drivers are held in tri-state (UG pulled to Phase, LG pulled to PGND) at the beginning of a soft-start cycle until two PWM pulses are detected. The low side MOSFET is turned on first to provide for charging of the bootstrap capacitor. This method of driver activation provides support for start-up into prebiased loads by not activating the drivers until the control loop has entered its linear region, thereby substantially reducing output transients that would otherwise occur had the drivers been activated at the beginning of the soft-start cycle. The OCP function is enabled with the drivers at start-up. OCP is implemented via a resistor (ROCSET) and a capacitor (COCSET) connecting the OCSET pin and the drain of the high side MOSEFT. An internal 200A current source develops a voltage across ROCSET, which is then compared with the voltage developed across the high side MOSFET at turn-on as measured at the PHASE pin. When the voltage drop across the MOSFET exceeds the voltage drop across the resistor, a sourcing OCP event occurs. COCSET is placed in parallel with ROCSET to smooth the voltage across ROCSET in the presence of switching noise on the input bus. A 120ns blanking period is used to reduce the current sampling error due to leading-edge switching noise. An additional simultaneous 120ns low pass filter is used to further reduce measurement error due to noise. OCP faults cause the regulator to disable (upper and lower drives disabled, SSDONE pulled low, soft-start capacitor discharged) itself for a fixed period of time, after which a normal soft-start sequence is initiated. If the voltage on the SS pin is already at 4V and an OCP is detected, a 30mA current sink is immediately applied to the SS pin. If an OCP is detected during soft-start, the 30A current sink will not be applied until the voltage on the SS pin has reached 4V. This current sink discharges the CSS capacitor in a linear fashion. Once the voltage on the SS pin has reached approximately 0V, the normal soft-start sequence is initiated. If the fault is still present on the subsequent restart, the ISL6535 will repeat this process in a hiccup mode. Figure 4 shows a typical reaction to a repeated overcurrent condition that places the regulator in a hiccup mode. If the regulator is repeatedly tripping overcurrent, the hiccup period can be approximated by Equation 5: 8V C SS t HICCUP = ----------------------30A (EQ. 5) SSDONE Soft-start done is only available in the 16 Ld QFN packaging option of the ISL6535. When the soft-start pin reaches 4V, an open drain signal is provided to support sequencing requirements. SSDONE is deasserted by disabling of the part, including pulling SS low, and by POR and OCP events. Oscillator The oscillator is a triangular waveform, providing for leading and falling edge modulation. The peak to peak of the ramp amplitude is set at 1.9V and varies as a function of frequency. At 50kHz the peak to peak amplitude is approximately 1.8V while at 1.5MHz it is approximately 2.2V. In the event the regulator operates at 100% duty cycle for 64 clock cycles an automatic boot cap refresh circuit will activate turning on LG for approximately 1/2 of a clock cycle. 7 FN9255.1 May 5, 2008 ISL6535 The OCP trip point varies mainly due to MOSFET rDS(ON) variations and layout noise concerns. To avoid overcurrent tripping in the normal operating load range, find the ROCSET resistor from the following equations with: 1. The maximum rDS(ON) at the highest junction temperature 2. The minimum IOCSET from the specification table Determine the overcurrent trip point greater than the maximum output continuous current at maximum inductor ripple current. SIMPLE OCP EQUATION I OC_SOURCE * r DS ( ON ) R OCSET = --------------------------------------------------------------200A Application Guidelines Layout Considerations As in any high frequency switching converter, layout is very important. Switching current from one power device to another can generate voltage transients across the impedances of the interconnecting bond wires and circuit traces. These interconnecting impedances should be minimized by using wide, short printed circuit traces. The critical components should be located as close together as possible using ground plane construction or single point grounding. A multi-layer printed circuit board is recommended. Figure 5 shows the critical components of the converter. Note that capacitors CIN and COUT could each represent numerous physical capacitors. Dedicate one solid layer (usually a middle layer of the PC board) for a ground plane and make all critical component ground connections with vias to this layer. Dedicate another solid layer as a power plane and break this plane into smaller islands of common voltage levels. Keep the metal runs from the PHASE terminals to the output inductor short. The power plane should support the input power and output power nodes. Use copper filled polygons on the top and bottom circuit layers for the phase nodes. Use the remaining printed circuit layers for small signal wiring. DETAILED OCP EQUATION I I + ---- * r OC_SOURCE 2 DS ( ON ) R OCSET = --------------------------------------------------------------------------------I HSOC * N U N U = NUMBER OF HIGH SIDE MOSFETs V IN - V OUT V OUT I = ------------------------------- * --------------f SW * L OUT V IN f SW = Regulator Switching Frequency (EQ. 6) VCC +12V CBP_PVCC High Speed MOSFET Gate Driver The integrated driver has the same drive capability and feature as the Intersil's 12V gate driver, ISL6612. The PWM tri-state feature helps prevent a negative transient on the output voltage when the output is being shut down. This eliminates the Schottky diode that is used in some systems for protecting the microprocessor from reversed-outputvoltage damage. See the ISL6612 datasheet FN9153 for specification parameters that are not defined in the current ISL6535 "Electrical Specifications" table on page 4. PVCC CBP_VCC ISL6535 VIN CIN Q1 UGATE BOOT CIN PHASE LOUT Reference Input The REFIN pin allows the user to bypass the internal 0.597V reference with an external reference. If REFIN is NOT above ~2.2V, the external reference pin is used as the control reference instead of the internal 0.597V reference. When not using the external reference option, the REFIN pin should be left floating. An internal 6A pull-up keeps this REFIN pin above 2.2V in this situation. VOUT LOAD FN9255.1 May 5, 2008 COUT LGATE SS GND PGND CSS Q2 Internal Reference and System Accuracy The Internal Reference is set to 0.597V. The total DC system accuracy of the system is to be within 1.0% over commercial temperature range and 1.5% over the industrial temperature range. System Accuracy includes Error Amplifier offset, and Reference Error. The use of REFIN may add up to 3mV of offset error into the system (as the Error Amplifier offset is trimmed out via the internal System reference). KEY TRACE SIZED FOR 3A PEAK CURRENT SHORT TRACE, MINIMUM IMPEDANCE ISLAND ON POWER PLANE LAYER ISLAND ON CIRCUIT AND/OR POWER PLANE LAYER VIA CONNECTION TO GROUND PLANE FIGURE 5. PRINTED CIRCUIT BOARD POWER PLANES AND ISLANDS 8 ISL6535 Locate the ISL6535 within 2 to 3 inches of the MOSFETs, Q1 and Q2 (1 inch or less for 500kHz or higher operation). The circuit traces for the MOSFETs' gate and source connections from the ISL6535 must be sized to handle up to 3A peak current. Minimize any leakage current paths on the SS pin and locate the capacitor Css close to the SS pin as the internal current source is only 30A. Provide local VCC decoupling between VCC and GND pins. Locate the capacitor CBOOT as close as practical to the BOOT pin and the phase node. C2 R2 C1 Compensating the Converter The ISL6535 Single-phase converter is a voltage-mode controller. This section highlights the design consideration for a voltage-mode controller requiring external compensation. To address a broad range of applications, a type-3 feedback network is recommended (see Figure 6). Figure 7 highlights the voltage-mode control loop for a synchronous-rectified buck converter. The output voltage is regulated to the reference voltage level. The error amplifier output is compared with the oscillator triangle wave to provide a pulse-width modulated wave with an amplitude of VIN at the PHASE node. The PWM wave is smoothed by the output filter. The output filter capacitor bank's equivalent series resistance is represented by the series resistor ESR. The modulator transfer function is the small-signal transfer function of VOUT /VCOMP. This function is dominated by a DC gain and shaped by the output filter, with a double pole break frequency at FLC and a zero at FCE . For the purpose of this analysis, L and DCR represent the output inductance and its DCR, while C and ESR represents the total output capacitance and its equivalent series resistance. 1 F LC = --------------------------2 L C 1 F CE = -------------------------------2 C ESR (EQ. 7) COMP FB C3 R3 R1 VOUT ISL6535 FIGURE 6. COMPENSATION CONFIGURATION FOR THE ISL6535 CIRCUIT C2 COMP R2 - C1 R3 C3 FB E/A + VREF GND R1 The compensation network consists of the error amplifier (internal to the ISL6535) and the external R1 to R3, C1 to C3 components. The goal of the compensation network is to provide a closed loop transfer function with high 0dB crossing frequency (F0; typically 0.1 to 0.3 of fSW) and adequate phase margin (better than 45). Phase margin is the difference between the closed loop phase at F0dB and 180. The equations that follow relate the compensation network's poles, zeros and gain to the components (R1 , R2 , R3 , C1 , C2 , and C3) in Figures 6 and 7. Use the following guidelines for locating the poles and zeros of the compensation network: 1. Select a value for R1 (1k to 10k, typically). Calculate value for R2 for desired converter bandwidth (F0). If setting the output voltage to be equal to the reference set voltage, as shown in Figure 7, the design procedure can be followed as presented. V OSC R 1 F 0 R 2 = --------------------------------------------D MAX V IN F LC (EQ. 8) OSCILLATOR VIN PWM CIRCUIT VOSC L VOUT UGATE HALF-BRIDGE DRIVE DCR As the ISL6535 supports 100% duty cycle, DMAX equals 1. The ISL6535 uses a fixed ramp amplitude (VOSC) of 1.9V, Equation 8 simplifies to Equation 9: 1.9 R 1 F 0 R 2 = -----------------------------V IN F LC (EQ. 9) PHASE C ESR LGATE ISL6535 EXTERNAL CIRCUIT FIGURE 7. VOLTAGE-MODE BUCK CONVERTER COMPENSATION DESIGN 2. Calculate C1 such that FZ1 is placed at a fraction of the FLC, at 0.1 to 0.75 of FLC (to adjust, change the 0.5 factor in Equation 10 to the desired number). The higher the quality factor of the output filter and/or the higher the ratio FCE/FLC, the lower the FZ1 frequency (to maximize phase boost at FLC). 9 FN9255.1 May 5, 2008 ISL6535 1 C 1 = ---------------------------------------------2 R 2 0.5 F LC (EQ. 10) 3. Calculate C2 such that FP1 is placed at FCE. C1 C 2 = ------------------------------------------------------2 R 2 C 1 F CE - 1 (EQ. 11) multiplying the modulator transfer function and the compensation transfer function and then plotting the resulting gain. FZ1 FZ2 GAIN FP1 FP2 MODULATOR GAIN COMPENSATION GAIN CLOSED LOOP GAIN OPEN LOOP E/A GAIN 4. Calculate R3 such that FZ2 is placed at FLC. Calculate C3 such that FP2 is placed below fSW (typically, 0.3 to 1.0 times fSW). fSW represents the switching frequency of the regulator. Change the numerical factor (0.7) below to reflect desired placement of this pole. Placement of FP2 lower in frequency helps reduce the gain of the compensation network at high frequency, in turn reducing the HF ripple component at the COMP pin and minimizing resultant duty cycle jitter. R1 R 3 = ------------------f SW ---------- - 1 F LC 1 C 3 = ---------------------------------------------2 R 3 0.7 f SW R2 20 log ------- R1 0 D V MAX IN 20 log --------------------------------V OSC GFB GCL LOG GMOD LOG FLC FCE F0 FREQUENCY (EQ. 12) FIGURE 8. ASYMPTOTIC BODE PLOT OF CONVERTER GAIN It is recommended that a mathematical model be used to plot the loop response. Check the loop gain against the error amplifier's open-loop gain. Verify phase margin results and adjust as necessary. The following equations describe the frequency response of the modulator (GMOD), feedback compensation (GFB) and closed-loop response (GCL): D MAX V IN 1 + s ( f ) ESR C G MOD ( f ) = ------------------------------ ---------------------------------------------------------------------------------------------------------2 V OSC 1 + s ( f ) ( ESR + DCR ) C + s ( f ) L C 1 + s ( f ) R2 C1 G FB ( f ) = --------------------------------------------------- s ( f ) R1 ( C1 + C2 ) 1 + s ( f ) ( R1 + R3 ) C3 ----------------------------------------------------------------------------------------------------------------------- C1 C2 ( 1 + s ( f ) R 3 C 3 ) 1 + s ( f ) R 2 -------------------- C 1 + C 2 G CL ( f ) = G MOD ( f ) G FB ( f ) where, s ( f ) = 2 f j (EQ. 13) A stable control loop has a gain crossing with close to a -20dB/decade slope and a phase margin greater than 45. Include worst case component variations when determining phase margin. The mathematical model presented makes a number of approximations and is generally not accurate at frequencies approaching or exceeding half the switching frequency. When designing compensation networks, select target crossover frequencies in the range of 10% to 30% of the switching frequency, fSW. Component Selection Guidelines Output Capacitor Selection An output capacitor is required to filter the output and supply the load transient current. The filtering requirements are a function of the switching frequency and the ripple current. The load transient requirements are a function of the slew rate (di/dt) and the magnitude of the transient load current. These requirements are generally met with a mix of capacitors and careful layout. Modern microprocessors produce transient load rates above 1A/ns. High frequency capacitors initially supply the transient and slow the current load rate seen by the bulk capacitors. The bulk filter capacitor values are generally determined by the ESR (effective series resistance) and voltage rating requirements rather than actual capacitance requirements. High frequency decoupling capacitors should be placed as close to the power pins of the load as physically possible. Be careful not to add inductance in the circuit board wiring that could cancel the usefulness of these low inductance components. Consult with the manufacturer of the load on specific decoupling requirements. Use only specialized low-ESR capacitors intended for switching-regulator applications for the bulk capacitors. The bulk capacitor's ESR will determine the output ripple COMPENSATION BREAK FREQUENCY EQUATIONS 1 F Z1 = -----------------------------2 R 2 C 1 1 F Z2 = ------------------------------------------------2 ( R 1 + R 3 ) C 3 1 F P1 = -------------------------------------------C1 C2 2 R 2 -------------------C1 + C2 1 F P2 = -----------------------------2 R 3 C 3 (EQ. 14) Figure 8 shows an asymptotic plot of the DC/DC converter's gain vs frequency. The actual Modulator Gain has a high gain peak dependent on the quality factor (Q) of the output filter, which is not shown. Using the previously mentioned guidelines should yield a compensation gain similar to the curve plotted. The open loop error amplifier gain bounds the compensation gain. Check the compensation gain at FP2 against the capabilities of the error amplifier. The closed loop gain, GCL, is constructed on the log-log graph of Figure 8 by adding the modulator gain, GMOD (in dB), to the feedback compensation gain, GFB (in dB). This is equivalent to 10 FN9255.1 May 5, 2008 ISL6535 voltage and the initial voltage drop after a high slew-rate transient. An aluminum electrolytic capacitor's ESR value is related to the case size with lower ESR available in larger case sizes. However, the equivalent series inductance (ESL) of these capacitors increases with case size and can reduce the usefulness of the capacitor to high slew-rate transient loading. Unfortunately, ESL is not a specified parameter. Work with your capacitor supplier and measure the capacitor's impedance with frequency to select a suitable component. In most cases, multiple electrolytic capacitors of small case size perform better than a single large case capacitor. capacitors for high frequency decoupling and bulk capacitors to supply the current needed each time Q1 turns on. Place the small ceramic capacitors physically close to the MOSFETs and between the drain of Q1 and the source of Q2. The important parameters for the bulk input capacitor are the voltage rating and the RMS current rating. For reliable operation, select a bulk capacitor with voltage and current ratings above the maximum input voltage and largest RMS current required by the circuit. The capacitor voltage rating should be at least 1.25 times greater than the maximum input voltage, a voltage rating of 1.5 times greater is a conservative guideline. The RMS current rating requirement for the input capacitor of a buck regulator is approximately 1/2 the DC load current. For a through hole design, several electrolytic capacitors (Panasonic HFQ series or Nichicon PL series or Sanyo MVGX or equivalent) may be needed. For surface mount designs, solid tantalum capacitors can be used, but caution must be exercised with regard to the capacitor surge current rating. These capacitors must be capable of handling the surge-current at power-up. The TPS series available from AVX, and the 593D series from Sprague are both surge current tested. Output Inductor Selection The output inductor is selected to meet the output voltage ripple requirements and minimize the converter's response time to the load transient. The inductor value determines the converter's ripple current and the ripple voltage is a function of the ripple current. The ripple voltage and current are approximated by Equation 15: V IN - V OUT V OUT I = ------------------------------- * --------------Fs x L V IN VOUT= I x ESR (EQ. 15) Increasing the value of inductance reduces the ripple current and voltage. However, the large inductance values reduce the converter's response time to a load transient. One of the parameters limiting the converter's response to a load transient is the time required to change the inductor current. Given a sufficiently fast control loop design, the ISL6535 will provide either 0% or 100% duty cycle in response to a load transient. The response time is the time required to slew the inductor current from an initial current value to the transient current level. During this interval the difference between the inductor current and the transient current level must be supplied by the output capacitor. Minimizing the response time can minimize the output capacitance required. The response time to a transient load is different for the application of load and the removal of load. The following equations give the approximate response time interval for application and removal of a transient load: L O x I TRAN t RISE = ------------------------------V IN - V OUT L O x I TRAN t FALL = -----------------------------V OUT (EQ. 16) MOSFET Selection/Considerations The ISL6535 requires at least 2 N-Channel power MOSFETs. These should be selected based upon rDS(ON), gate supply requirements, and thermal management requirements. In high-current applications, the MOSFET power dissipation, package selection and heatsink are the dominant design factors. The power dissipation includes two loss components; conduction loss and switching loss. At a 300kHz switching frequency, the conduction losses are the largest component of power dissipation for both the upper and the lower MOSFETs. These losses are distributed between the two MOSFETs according to duty factor (see Equation 17). Only the upper MOSFET exhibits switching losses, since the schottky rectifier clamps the switching node before the synchronous rectifier turns on. PUPPER = IO2 x rDS(ON) x D + 1 Io x VIN x tSW x fSW 2 PLOWER = IO2 x rDS(ON) x (1 - D) where: ITRAN is the transient load current step, tRISE is the response time to the application of load, and tFALL is the response time to the removal of load. With a +5V input source, the worst case response time can be either at the application or removal of load and dependent upon the output voltage setting. Be sure to check both of these equations at the minimum and maximum output levels for the worst case response time. where: D is the duty cycle = VO / VIN, tSW is the switching interval, and fSW is the switching frequency. (EQ. 17) Input Capacitor Selection Use a mix of input bypass capacitors to control the voltage overshoot across the MOSFETs. Use small ceramic These equations assume linear voltage-current transitions and do not adequately model power loss due the reverserecovery of the lower MOSFETs body diode. The gate-charge losses are dissipated by the ISL6535 and don't heat the MOSFETs. However, large gate-charge increases the switching interval, tSW which increases the upper MOSFET switching losses. Ensure that both MOSFETs are within their maximum junction temperature at high ambient 11 FN9255.1 May 5, 2008 ISL6535 temperature by calculating the temperature rise according to package thermal-resistance specifications. A separate heatsink may be necessary depending upon MOSFET power, package type, ambient temperature and air flow. Standard-gate MOSFETs are normally recommended for use with the ISL6535. However, logic-level gate MOSFETs can be used under special circumstances. The input voltage, upper gate drive level, and the MOSFETs absolute gate-tosource voltage rating determine whether logic-level MOSFETs are appropriate. Figure 9 shows the upper gate drive (BOOT pin) supplied by a bootstrap circuit from +12V. The boot capacitor, CBOOT develops a floating supply voltage referenced to the PHASE pin. This supply is refreshed each cycle to a voltage of +12V less the boot diode drop (VD) when the lower MOSFET, Q2 turns on. A MOSFET can only be used for Q1 if the MOSFETs absolute gate-to-source voltage rating exceeds the maximum voltage applied to +12V. For Q2, a logic-level MOSFET can be used if its absolute gate-to-source voltage rating also exceeds the maximum voltage applied to +12V. +12V DBOOT + VD BOOT CBOOT UGATE PHASE PVCC + LGATE PGND GND +12V Q2 D2 NOTE: VG-S PVCC Q1 GND NOTE: VG-S VCC - VD +1.2V TO +12V + Figure 10 shows the upper gate drive supplied by a direct connection to +12V. This option should only be used in converter systems where the main input voltage is +5 VDC or less. The peak upper gate-to-source voltage is approximately +12V less the input supply. For +5V main power and +12V DC for the bias, the gate-to-source voltage of Q1 is 7V. A logic-level MOSFET is a good choice for Q1 and a logic-level MOSFET can be used for Q2 if its absolute gate-to-source voltage rating exceeds the maximum voltage applied to PVCC. This method reduces the number of required external components, but does not provide for immunity to phase node ringing during turn on and may result in lower system efficiency. +12V +5V OR LESS ISL6535 BOOT UGATE Q1 NOTE: VG-S VCC - 5V PVCC LGATE PGND +12V Q2 D2 NOTE: VG-S PVCC ISL6535 FIGURE 10. UPPER GATE DRIVE - DIRECT VCC DRIVE OPTION Schottky Selection Rectifier D2 is a clamp that catches the negative inductor swing during the dead time between turning off the lower MOSFET and turning on the upper MOSFET. The diode must be a Schottky type to prevent the lossy parasitic MOSFET body diode from conducting. It is acceptable to omit the diode and let the body diode of the lower MOSFET clamp the negative inductor swing, but efficiency could slightly decrease as a result. The diode's rated reverse breakdown voltage must be greater than the maximum input voltage. FIGURE 9. UPPER GATE DRIVE - BOOTSTRAP OPTION 12 FN9255.1 May 5, 2008 ISL6535 Small Outline Plastic Packages (SOIC) N INDEX AREA H E -B1 2 3 SEATING PLANE -AD -CA h x 45o 0.25(0.010) M BM M14.15 (JEDEC MS-012-AB ISSUE C) 14 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE INCHES SYMBOL A L MILLIMETERS MIN 1.35 0.10 0.33 0.19 8.55 3.80 5.80 0.25 0.40 14 0o MAX 1.75 0.25 0.51 0.25 8.75 4.00 6.20 0.50 1.27 8o NOTES 9 3 4 5 6 7 Rev. 0 12/93 MIN 0.0532 0.0040 0.013 0.0075 0.3367 0.1497 0.2284 0.0099 0.016 14 0o MAX 0.0688 0.0098 0.020 0.0098 0.3444 0.1574 0.2440 0.0196 0.050 8o A1 B C D E e C A1 0.10(0.004) e B 0.25(0.010) M C AM BS 0.050 BSC 1.27 BSC H h L N NOTES: 1. Symbols are defined in the "MO Series Symbol List" in Section 2.2 of Publication Number 95. 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 4. Dimension "E" does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm (0.010 inch) per side. 5. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 6. "L" is the length of terminal for soldering to a substrate. 7. "N" is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. The lead width "B", as measured 0.36mm (0.014 inch) or greater above the seating plane, shall not exceed a maximum value of 0.61mm (0.024 inch). 10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. 13 FN9255.1 May 5, 2008 ISL6535 Quad Flat No-Lead Plastic Package (QFN) Micro Lead Frame Plastic Package (MLFP) L16.4x4 16 LEAD QUAD FLAT NO-LEAD PLASTIC PACKAGE (COMPLIANT TO JEDEC MO-220-VGGC ISSUE C) MILLIMETERS SYMBOL A A1 A2 A3 b D D1 D2 E E1 E2 e k L L1 N Nd Ne P 0.25 0.50 1.95 1.95 0.23 MIN 0.80 NOMINAL 0.90 0.20 REF 0.28 4.00 BSC 3.75 BSC 2.10 4.00 BSC 3.75 BSC 2.10 0.65 BSC 0.60 16 4 4 0.60 12 0.75 0.15 2.25 2.25 0.35 MAX 1.00 0.05 1.00 NOTES 9 9 5, 8 9 7, 8 9 7, 8 8 10 2 3 3 9 9 Rev. 5 5/04 NOTES: 1. Dimensioning and tolerancing conform to ASME Y14.5-1994. 2. N is the number of terminals. 3. Nd and Ne refer to the number of terminals on each D and E. 4. All dimensions are in millimeters. Angles are in degrees. 5. Dimension b applies to the metallized terminal and is measured between 0.15mm and 0.30mm from the terminal tip. 6. The configuration of the pin #1 identifier is optional, but must be located within the zone indicated. The pin #1 identifier may be either a mold or mark feature. 7. Dimensions D2 and E2 are for the exposed pads which provide improved electrical and thermal performance. 8. Nominal dimensions are provided to assist with PCB Land Pattern Design efforts, see Intersil Technical Brief TB389. 9. Features and dimensions A2, A3, D1, E1, P & are present when Anvil singulation method is used and not present for saw singulation. 10. Depending on the method of lead termination at the edge of the package, a maximum 0.15mm pull back (L1) maybe present. L minus L1 to be equal to or greater than 0.3mm. All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation's quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 14 FN9255.1 May 5, 2008 |
Price & Availability of ISL6535CBZ
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |